Search results

Most stuff are 50% off while a few I'm seeing at 75%. Shipping is free over $19.

I know for fish this is a recipe for a disaster but does it apply to corals too? Yesterday I picked up 3 frags of zoas, a frag of palys and a frag of gsp. This weekend I plan on checking out americanreefs and picking up another $50 or so from their $5-10 section. This will be in a 40g and I have...

Tennis ball to softball size. No frags available for exchange but can do a few bucks in cash. TIA.

These seem to have been out for a few months now but haven't seen much discussions about them. They look to be a mix of the many wavemakers out there and the vortechs. They still have a cable going inside the tank but are short like the MPs. Flow is suppose to be very wide too. I have one on...

Ecoxotic LEDs - 3 strips (blue, blue/white, white) with controller and remote (needs new battery) Clamp on LED (blue/white) Odyssea 24" T5/MH with hanging brackets. Needs ballast for MH. Not sure life on bulbs. As it. Looking for powerheads/wavemakers, ato reservoir, reefkeeper...

Was trying to get everything wired up last night but I'm getting nothing on the SL2 module. No status light and it's not being seen by the RKL. This is the first version and not the v2. It'll actually trip the PC4 powerbar after a few minutes causing the status light on the PC4 to start blinking...

I have a prefab stand that is a little too short. I'd like to raise it atleast 6", maybe even 8. I'm thinking of constructing a riser using 1x6 or 1x8 for the sides, front and another in the middle---> |_|_|. Rear is open to save on having to buy 2 boards. Top will be 1/2 plywood. Would this be...

I'm assuming if the power goes out and a siphon occurs the water will flow back and level off at the level on the display side correct? So even if the returns are too low and the water level of display side never breaks below them the water should equal out? I can see that if the display side...

My plan is to make 2 media caddys to fit inside the area behind the dual overflows. I'm using 1/4" black acrylic and black egg crate. I got the acrylic yesterday and got them cut to size on the tile table saw. They will be U shaped with the front open to easily remove whatever media is used...

How accurate are they with the cuts? Need to cut a 4x8 sheet down to skin my metal stand.

Wow can't believe it's been 2 years. Anyways I still have my AIO sitting in the garage along with just about everything else needed to get it up except for a stand. Was gonna have that custom built but the builder dropped out of the deal. I do have one coming in today. :whoo: Got a new return...

Pickup in Fontana. Can meet after 4pm M-F in Pasadena area or along my commute home. ***5g rimless with pump/filter, no lid or lights (exactly as pictured) - $25 ***8g AIO with pump, mesh lid, glass lids but missing clips, no filter medium or lights - $50 EcoExotics LED lights mounted on...

I need just the strip. Must be the 445nm all blue one.

I'm thinking of other ways to finish a stand being built rather than just painting or staining and thought covering it with textured wallpaper might look pretty good. I foresee the only issue might be moisture from splashes and drips but I think if I'm diligent in wiping it quickly it should be...

So I just ordered 15lb of base dry rock, 10lb of dry shelf rock, and 10lb of live cured rock for my new build. I'm going to cure the live rock for about 2 weeks to get rid of all the die off from the transport. Can I cure the dry rocks with this together or would it be better to do them...

After a 3.5 week wait I finally picked her up today from AA. She's a beast at 3/4" all around. Outside dims are 36x20x15h. Display area is about 14"w with the rear section at 4". Dual overflows with a center compartment for the return pump, a skimmer compartment and a fuge. I will be looking to...

Every single day I have to upright or pick my frags off the sand bed cause the mf just bulldoze his way through everything. I've already lost a few frags cause they were knocked down and landed face down in the sand. I'm really close to pulling it out and just stomping on his a$$.

Probably a long shot but can't hurt to try. Looking for a 36" 250w mh with t5 in either 2x39 or 4x39. MH must be double edge. With or without ballast is fine. TIA

They all pretty much look the same. Are they just resellers of a chinese manufacturer/supplier?

With many electronics if you flashed it with the wrong firmware you pretty much just bricked it. That's what I thought I did with my rkl. My dumbass flashed it with the RD1 firmware. Plugged it in after and it says wrong firmware. Tried forcing the RKL firmware but it says firmware does not...