Search results

My side? Is that an option. In a seriousness tho man. I’m tried of being a negative person. Man! Look at most successful people they don’t put down and hate on others no they try to raise others around them to there success. It doesn’t have to be lonely at the top.

I see the points. But isn’t it the point of every company to grow. Congratulations to BRS from turning a online retailer of affordable carbon and gfo to an Aqua industry power house. Things won’t always stay the same in life you either adapt or get left in the dust

SOB now I wanna go back to MH. [emoji2959] that is looking wonderful

Well I’ll start off by saying thanks to TurboNut (Omar) for shooting out and giving me, wife, and daughter a hand. Secondly let’s just say siliconing a large tank is extremely hard. Ok maybe not hard but is pretty difficult to get done cleanly. But we got the seams sealed So I got the...

Well me Omar and wife and daughter got this done. Thank turbo

So let generate a little biz. Got ARC fireworks, GC ultimate efflo, PC rainbow, ADS rainbow milli, forestfire digi, bam bam zoas, a RBTA or 2, seasons greetings monti……

Did some final wet polishing to the sides this morning They came out really clear. A slight line of etching but it will be hidden by silicone Everything is taped and ready to go. Just need some hands to silicone everything in place Got tape on the bottom to hold the sides from sliding out...

Sweet. Need the addie again?

Free coral frags with a small donation of an hour of your time. I need a few hands to hold panels and help set panels on an aquarium I’m re-building. I found out yesterday that the miss and kids aren’t really strong enough to help or there just lazy (I’m bettin lazy [emoji6]) Location is in...

So I’m wondering if there’s any guys out there that would be willing to give me a hand assembling this thing later this afternoon. I’ll even buy pizza and wings. I also have plenty of sps frags I can give out. So hit me up if interested. It should only take an hour or so. Location perris

Man I thought about ordering a large piece of 1/2” thick glass and seeing if it would be easier to cut new regular glass. In all honesty I’m having a lot of fun doing all the different trades. Granted I’m spending a lot of time that I don’t have much of during the summer (cause of work). But...

Front pain taped.

So I got the tank mocked up. Just need to make all my marks and measurements. Later tonight I’m going to tape off the glass. Then hopefully tomorrow I can get this b**** siliconed.

In the vid I was working with regular glass I think that’s why it was easier to cut. The low iron had a lot of chipping and not many of the breaks were on the score perfectly. Even when I was tapping on the glass with the back of the glass trying to get a run to occur the glass was getting...

Another zonk guys. The glass is to soft and old to make thin strips But I was at least able to cut it down into more manageable pieces Dose any buddy know if Steve will be into taking these or should I just trash it Edit: nvm I remembered that I still had Steve’s cell so I just shoot him a...

Once I get the ac fixed I’ll attempt again. I’ll just try the tapping method, to create a run line. Hopefully that will work on these long ass strips. Figured out why the ac was leaking tho. The installer that installed the new unit in the attic didn’t use teflon tape when installing the...

Hey don’t you have like corals to buy or fish to purchase. Stop pissin on my parade. [emoji23]

So later I’ll try doing the tapping method to create a run line. But first I have bigger fish to fry So this is the ceiling on the second story and that is a shit load of water dripping. After crawling my fat ass up in the attic I found that the AC condensation drain line and the emergency...

You good sir, you are good. So after doing 4 successfully practices cuts on the old Eurobrace I was like let’s attempt the big boy. So I cleaned the table off. Got a really good score on the glass Then got the piece into a position where it would be easier to use the running pliers and there...

Well my glass cutting equipment came yesterday while I was at work. So you know me mister impatient I need to eff with it as soon as I get home. Well here’s the kit Scorer(aka glass cutter), cutting oil, and running pliers So here’s the first piece of glass I’m going to attempt to cut. It’s a...